Drill Bit Size Chart: What Size Bit for Screws, Tapcons and Bolts

Not sure if this category is right for you? Take the tool finder quiz →

This post contains affiliate links. We earn a commission when you purchase through our links at no extra cost to you.

Researched by Moses Washika · Updated November 2026

What to know
  • For wood screws, drill a pilot hole a little smaller than the screw’s core so the threads bite: 5/64″ for a #8 screw in softwood and 3/32″ in hardwood.
  • Drill a clearance hole the size of the screw shank through the top board so the joint pulls tight. For a #8 screw that is 11/64″.
  • For Tapcon concrete screws, use a 5/32″ bit for 3/16″ screws and a 3/16″ bit for 1/4″ screws.
  • For tapping bolt threads, a 1/4″-20 bolt needs a #7 drill and an M6 bolt needs a 5 mm drill.

Picking the right drill bit is the difference between a screw that holds and one that splits the board or spins loose. The rule is simple once you know it, and the charts below cover the sizes most people use.

Use the finder for a quick answer, then check the full charts for wood screws, concrete screws and bolt threads. Sizes come from published fastener charts, linked below.

Drill bit size finder

What size drill bit do I need?

Pick what you are fixing and the size. We show the bit to use and how deep to drill.

Wood screw pilot hole chart

Screw sizeHardwood pilotSoftwood pilotClearance hole
#41/16″3/64″1/8″
#65/64″1/16″9/64″
#83/32″5/64″11/64″
#107/64″3/32″3/16″
#121/8″7/64″7/32″
#149/64″1/8″1/4″

Pilot sizes from Engineers Edge. Clearance holes match the screw’s shank diameter. Some makers suggest slightly larger pilots for self drilling or square drive screws, so test on scrap.

The screw number is its diameter, not its length. A #8 screw is about 0.164 inch across the shank whether it is 1 inch or 3 inches long.

Not sure which screw you have? Lay it over the bits in your set. The pilot bit should hide the solid core but leave the threads showing on each side.

Pilot holes and clearance holes explained

  • Pilot hole: a small hole in the board the screw goes into. It stops the wood splitting and keeps the screw straight.
  • Clearance hole: a larger hole through the top board. The screw slides through it, so the head pulls the two boards together.
  • Countersink: a cone at the top so a flat head screw sits flush. A combination countersink bit drills all three in one go.

Hardwood needs a pilot hole a size larger than softwood, because dense wood splits more easily. Near the end of a board, always drill a pilot, even in softwood.

Concrete and masonry drill bit sizes

Concrete screws need a carbide tipped masonry bit and a hammer drill. The bit must match the screw exactly, or the threads will not cut properly.

Concrete screwBit sizeMinimum embedmentHole depth
3/16″ Tapcon5/32″1″At least 1/4″ deeper than the screw goes in
1/4″ Tapcon3/16″1″At least 1/4″ deeper than the screw goes in

Source: Confast Tapcon guide.

Blow or vacuum the dust out of the hole before driving the screw. Choosing a hammer drill? See our best cordless drills guide.

Tap drill chart for bolts and machine screws

To cut threads in metal with a tap, drill a hole slightly smaller than the bolt. These sizes give about 75% thread, the usual standard for most work.

ThreadTap drill
#6-32#36 (0.1065″)
#8-32#29 (0.136″)
#10-24#25 (0.1495″)
#10-32#21 (0.159″)
1/4″-20#7 (0.201″)
5/16″-18F (0.257″)
3/8″-165/16″
1/2″-1327/64″
M4 x 0.73.3 mm
M5 x 0.84.2 mm
M6 x 1.05.0 mm
M8 x 1.256.8 mm
M10 x 1.58.5 mm
M12 x 1.7510.2 mm

If a bolt only needs to pass through a part, drill a clearance hole instead. A clearance hole is a little larger than the bolt, such as 17/64″ for a 1/4″ bolt.

Drill bit sizes for drywall anchors

Plastic drywall anchors come in many sizes, and each maker prints the bit size on the pack. Use that size, because a hole even slightly too big lets the anchor spin.

  • Ribbed plastic anchors: follow the bit size on the pack and tap the anchor in flush.
  • Self drilling anchors: need no pilot hole in drywall; drive them in with a screwdriver.
  • Toggle bolts: need a large hole for the folded wings, also printed on the pack.
  • Heavy items: screw into a stud where you can. Find it with a stud finder.

Tips for clean, accurate holes

  • Mark and punch first. A small dent from a nail or center punch stops the bit wandering.
  • Use the right bit. Brad point bits for wood, twist bits for metal, masonry bits for concrete.
  • Let the bit cut. Too much pressure overheats bits and burns wood.
  • Use tape as a depth stop. Wrap tape around the bit at the depth you need.
  • Back out to clear chips in deep holes, and add oil when drilling steel.
  • Set the clutch on your drill so screws stop at the surface. See impact driver vs drill.

Drill bit sets worth owning

A good set covers most of the sizes above. Look for fractional sizes from 1/16″ to 1/4″ in 1/64″ steps, plus a few masonry bits.

Set typeBest forShop
Titanium coated twist bit setGeneral wood, plastic and light metalSee twist bit sets
Cobalt bit setStainless steel and hard metalSee cobalt sets
Brad point setClean holes in wood and furnitureSee brad point sets
Masonry bit setConcrete, brick and blockSee masonry sets
Countersink bit setPilot, clearance and countersink in oneSee countersink sets
Tap and drill setCutting threads in metalSee tap sets

Building a basic kit? Our first apartment tool kit and gifts for DIYers guides list the essentials.

Frequently asked questions

What size drill bit for a #8 wood screw?

Use a 5/64″ pilot bit in softwood and a 3/32″ bit in hardwood. For the clearance hole through the top board, use an 11/64″ bit.

What size drill bit for a #10 wood screw?

Use a 3/32″ pilot bit in softwood and a 7/64″ bit in hardwood. The clearance hole is 3/16″.

What size bit for a 1/4 inch Tapcon?

A 1/4″ Tapcon needs a 3/16″ carbide masonry bit. A 3/16″ Tapcon needs a 5/32″ bit.

What size drill bit for a 1/4-20 tap?

Use a #7 drill, which is 0.201 inch. A 13/64″ bit is a close fractional substitute.

Do I need a pilot hole for drywall screws?

Not in softwood or drywall, but drill one in hardwood or near the end of a board to prevent splitting.

How do I know what size my screw is?

Hold it against the bits in your set or a screw gauge. The number, such as #8, is the diameter; the length is listed separately in inches.

Similar Posts