How to Sharpen a Chainsaw Chain: File Size, Angle and Step by Step Guide

Not sure if this category is right for you? Take the tool finder quiz →

This post contains affiliate links. We earn a commission when you purchase through our links at no extra cost to you.

Researched by Moses Washika · Updated November 2026

What to know
  • File each cutter with a round file matched to your chain pitch, usually at a 30° angle, using smooth forward strokes only.
  • Give every cutter the same number of strokes, then file the depth gauges every 3 to 5 sharpenings.
  • Most homeowner saws use 3/8 low profile chain and a 5/32 inch file. The finder below confirms yours.

A sharp chain throws big, even chips and pulls itself into the wood. A dull one makes dust, smokes and wears you out, and it is more likely to kick back.

This guide shows how to sharpen a chainsaw chain by hand in about 15 minutes, with the right file size, angles and depth gauge settings from STIHL, Husqvarna and Oregon guidance. The finder gives you the exact numbers for your chain.

Chainsaw file size finder

Chainsaw file size finder

Pick your chain pitch and the wood you cut. We show the round file, the angle and the depth gauge setting. The pitch is stamped on the drive links or printed on the bar.

Chain pitchRound fileTypical saw
1/4 inch5/32 in (4.0 mm)Small top handle and pole saws
3/8 inch low profile (3/8 LP)5/32 in (4.0 mm)Most homeowner, electric and battery saws
.325 inch3/16 in (4.8 mm)Mid size gas saws, 40 to 50 cc
3/8 inch standard7/32 in (5.5 mm)Larger gas saws, 50 cc and up
.404 inch7/32 in (5.5 mm)Big pro and harvester saws

File sizes from the Zoro chainsaw file size chart, which also lists 11/64 inch (4.5 mm) for STIHL .325 pro chain. Always check the size printed on your chain box.

Signs your chain is dull

  • Sawdust instead of chips. A sharp chain throws large, even chips.
  • You have to push. A sharp saw pulls itself in under its own weight.
  • Smoke from the cut, even with good bar oil and correct tension.
  • The cut wanders or the saw pulls to one side, a sign of uneven cutters.
  • The saw chatters and bounces in the cut.

Signs from STIHL’s sharpening guide and Husqvarna Chainsaw Academy.

Tools you need

  • Round file in the right diameter for your chain pitch.
  • File guide or holder that sets the height and angle. Oregon and STIHL sell kits with the file included.
  • Flat file and depth gauge tool for the rakers.
  • Bench vise to hold the bar. See best bench vises.
  • Marker to mark your first cutter.
  • Gloves. Cutters are sharp even when dull. See cut resistant gloves.

Browse chainsaw sharpening kits on Amazon →

How to sharpen a chainsaw chain, step by step

  1. Clean and inspect the chain. Wipe off oil and sawdust and look for cracked or broken cutters. If cutters reach the wear mark, replace the chain.
  2. Clamp the bar in a vise. Snug the chain tension slightly and engage the chain brake so the bar and chain stay put.
  3. Mark the first cutter. Start on the shortest cutter so every other tooth matches it.
  4. Set the file. Hold it level, at 90° to the bar, with about a fifth to a quarter of its diameter above the top plate. Line it up with the angle mark on the cutter, usually 30°.
  5. File forward only. Push smooth, firm strokes from the inside of the cutter out, and lift the file on the way back. Rotate the file now and then so it wears evenly.
  6. Count your strokes. Give every cutter on that side the same number, usually 3 to 5.
  7. Turn the saw around and repeat on the cutters facing the other way.
  8. Check the edges. A sharp cutter shows no shiny reflection on its cutting edge.

STIHL says its chains are generally filed to 30 degrees and that the file should sit a quarter above the tooth. Husqvarna gives 25 to 35 degrees depending on chain type, so the mark on your chain wins. Sources: STIHL, Husqvarna.

How to file the depth gauges

In front of each cutter is a small hump called the depth gauge or raker. It decides how deep each tooth bites. As you sharpen, the cutters get shorter, so the rakers need lowering too.

  1. Lay a depth gauge tool across the chain so one raker pokes through the slot.
  2. File the raker flat with a flat file until it is flush with the tool.
  3. Round off the front edge slightly to match its original shape.
  4. Repeat for every raker.
WoodDepth gauge setting
SoftwoodAbout 0.025 in
Hardwood or frozen woodAbout 0.020 in

Check the rakers every 3 to 5 sharpenings. Filing them too low makes the saw grab and raises kickback risk, which STIHL warns about directly. Oregon sells a depth gauge tool set to 0.025 inch.

Common sharpening mistakes

  • Wrong file size. Too small digs a hook, too big leaves a blunt edge.
  • Filing on the back stroke. It dulls the file and rounds the edge.
  • Uneven cutters. The saw pulls to the side with the longer teeth.
  • Ignoring the rakers. A sharp chain with high rakers still cuts slowly.
  • Rakers too low. The saw grabs and kicks.
  • Hitting dirt. One stone dulls a chain instantly. Keep the tip off the ground.

File vs electric chainsaw sharpener

Hand file and guideElectric bench sharpener
CostLowHigher
Speed10 to 20 minutesA few minutes once set up
WhereAnywhere, even on the jobAt the bench, needs power
Metal removedVery little, chains last longerMore, unless set carefully
Best forMost homeownersSeveral chains or heavy use

Compare electric chain sharpeners on Amazon →

When to replace the chain

Replace the chain when the cutters reach the wear mark, when the top plate is shorter than about 4 mm, or when teeth crack or break. Husqvarna uses the 4 mm figure as its replacement point.

Keep a spare chain so you can swap it in the field and sharpen the dull one later. Need a new saw? See our best chainsaws for homeowners and Husqvarna vs STIHL. Cutting firewood this winter? Read best log splitters.

Find replacement chains on Amazon →

Always wear chaps, eye and hearing protection when you run the saw. See PPE for each task and NRR rated ear protection.

Frequently asked questions

How do I know my chainsaw needs sharpening?

It makes fine sawdust instead of chips, you have to push it into the wood, it smokes even with oil and correct tension, or it pulls to one side. STIHL lists all four as signs of a dull chain.

What angle do you sharpen a chainsaw chain?

Most chains are filed at 30 degrees on the top plate, with the file held level at 90 degrees to the bar. Husqvarna gives a range of 25 to 35 degrees depending on the chain, so follow the witness mark on your cutters.

What size file do I need for my chainsaw?

It depends on the chain pitch: 5/32 inch for 3/8 low profile and 1/4 inch chain, 3/16 inch for .325 inch chain, and 7/32 inch for 3/8 inch standard and .404 inch chain.

How many strokes per tooth when sharpening a chainsaw?

There is no fixed number. Give every cutter the same number of firm forward strokes, usually 3 to 5 on a lightly dull chain, and add strokes only to cutters that are shorter or damaged.

How often should I sharpen my chainsaw?

Touch it up whenever cutting slows, and check it at every refuel if you saw all day. A chain that hits dirt or a stone needs sharpening right away.

When should I replace a chainsaw chain instead of sharpening it?

Replace it when the cutters reach the wear mark, when the top plate is shorter than about 4 mm, or when you find cracked or broken teeth.

Is an electric chainsaw sharpener better than a file?

A bench grinder sharpener is faster and very even if you set it up carefully, which suits people with several chains. A file is cheap, works in the field and removes less metal, so chains last longer.

Similar Posts